[Supras] Trying to search old archives..HELP

[Jim Jobe]

I agree too, was just providing the post.

I've seen stockers take 500ft-lbs of torque with ease.  I'd rather spend a few
bucks more for OEM that fit and work well than hack on something for hours.

On Sat, Jul 29, 2006 at 12:03:05PM -0700, Jeff Mohler wrote:
> I dunno man, hard to say there is anything wrong with a mount thats
> 15yrs old..then it fails.
> 
> Like alternators, fan clutches, and anything else non-toyota as a
> replacement part, yer takin a bet.
> 
> On 7/29/06, Colin Adams <mkiiiman89 at gmail.com> wrote:
> >Are these just stock replacements that are cheaper? Or is there some sort 
> >of
> >other benefit to them?
> >
> >-Colin
> >
> >On 7/29/06, Jim Jobe <jjobe2 at supratech.org> wrote:
> >>
> >>
> >> Here's an old post:
> >>
> >> > "Just asked the guy at the local napa associated store to see the motor
> >> > mount book and had my mount for comparison. These are old time parts
> >> guys
> >> > (father and son store) and don't mind helping with non-aplication
> >> specific
> >> > things.
> >> >
> >> > Parts: motor mounts for mid 90s maxda/ford pick-up with 4 cyl (NAPA
> >> > 602-1686). 7/16" mag wheel lug nuts (Dorman 711-108 or equivalent), 12 
> >X
> >> > 1.75 mm tap, 11/16" and 7/16" drill bits, Here is the proceedure:
> >> >
> >> > 1. Drill out the aluminum bracket to 11/16" (the 1 hole the mount stud
> >> goes
> >> > through).
> >> >
> >> > 2. Buy a set of 7/16" mag wheel lug nuts, drill out the threads just
> >> enough
> >> > to take off the tops of the threads, then retap the nuts to 12 X 
> >1.75mm.
> >> > The nut will go through the bracket just like on a mag wheel. Nobody
> >> makes a
> >> > mag nut in 12 X 1.75, at least not that I could find, and only Ford 
> >uses
> >> > this thread on some of their trucks.
> >> >
> >> > 3. Trim the top side pin so it will go into the bracket, and remove the
> >> > bottom pin, I used a cut-off tool.
> >> >
> >> > 4. Buy 2 12 X 1.75 strut mount nuts (self-locking) and 1/2" washers for
> >> the
> >> > bottom stud."
> >> >
> >> > Todd
> >> > 89T
> >> >
> >> >
> >>
> >>
> >> On Sat, Jul 29, 2006 at 03:27:59AM -0400, SPOOLED91T at aol.com wrote:
> >> > I made a post probalby 3 years ago about some replacement motor mounts 
> >i
> >> > found at Oreilly's. Included was the part number and other info. I need
> >> to find
> >> > this info to order another mount, but cant find anything trying to
> >> search the
> >> > archives. Please help!!
> >> >
> >> > Jason  Green
> >> > 91 MA71T
> >> > 05 XRunner
> >> >
> >> > _______________________________________________
> >> > Supras mailing list
> >> > Supras at supras.com
> >> > http://supras.com/mailman/listinfo/supras_supras.com
> >>
> >> _______________________________________________
> >> Supras mailing list
> >> Supras at supras.com
> >> http://supras.com/mailman/listinfo/supras_supras.com
> >>
> >_______________________________________________
> >Supras mailing list
> >Supras at supras.com
> >http://supras.com/mailman/listinfo/supras_supras.com
> >